Fort Washington, PA Electrician for Offices, Older Homes and Backup Power
Office park circuits and after hours cutovers, standby generators, service repairs, panel upgrades and rewiring, across Fort Washington and Upper Dublin Township. Flat pricing, approved by you before we start.
- ●HIC License PA197924
- ●15+ Years Experience
- ●OSHA 30 Certified Technicians
- ●Fully Insured
- ●Same Day Service Available
- ●Upfront Flat Pricing
TotalPower Electrical Services is a licensed electrical contractor serving Fort Washington, PA and Upper Dublin Township. We handle office park and corporate electrical, server room circuits, three phase work, standby generators, panel upgrades, rewiring and emergency repairs. The company holds HIC License PA197924, employs OSHA 30 certified technicians, and quotes flat pricing before work begins.
Two very different phones ring for us out of 19034. One is a facilities manager in the office park off Pennsylvania Avenue or Virginia Drive who needs circuits added in a suite that has to stay open Monday morning. The other is a homeowner on one of the older roads with a stone house, walls close to two feet thick, and wiring that predates most of the appliances plugged into it.
Both come with a third category, and it comes up here more than almost anywhere else we work: backup power. Upper Dublin took serious storm damage a few years back, and since then the questions about standby generators, transfer switches and torn service masts have never really stopped. We answer all three kinds of call. Our crews also run daily in the city as licensed electricians in Philadelphia, so commercial and old residential are both routine rather than one being a sideline.
Where Electrical Problems Show Up in Fort Washington Buildings
Electrical service work covers everything from the utility connection at the meter to the last device on the last circuit. In a commercial suite that means the service, the distribution panels, the feeders, the branch circuits and every receptacle and fixture beyond. In a house it means the same chain at a smaller scale. The failures tend to cluster in predictable places, and knowing where saves diagnostic hours.
An office manager on Commerce Drive called us about a comms closet where the switches kept rebooting. Somebody had tapped the rack off a general receptacle circuit shared with a break room, and every time the microwave and the kettle ran together, the voltage sagged enough to matter. The fix was a dedicated circuit and about four hours of work. The diagnosis was the hard part, and it was free once we knew where to look.
Here is what tends to bring us out, on either side of the market:
- Server, comms or rack equipment sharing a circuit with anything else
- Breakers tripping when office equipment or HVAC cycles together
- A suite fit out where the new layout needs circuits the building never had
- Exit or emergency lighting that fails a fire inspection test
- A service mast, weatherhead or meter socket damaged by a storm or a falling limb
- No backup power in a building or home that cannot afford an outage
- Live knob and tube or cloth insulated wiring in an older house
- A 60 or 100 amp residential service running a modern kitchen and central air
- Outlets, switch plates or panel covers that feel warm, or show scorch marks
- Repeated equipment failures after storms, which usually points to surge exposure
Our Electrical Services in Fort Washington, PA
One crew, one point of contact, and nothing farmed out to a subcontractor you never met.
Office Park and Corporate Electrical
Suite fit outs, added circuits, workstation power and lighting across the Fort Washington office park, scheduled around your operating hours rather than through them. We coordinate with property management on access, freight and after hours HVAC. Part of our commercial electrical contracting.
Server and Comms Room Circuits
Dedicated circuits sized to the load, isolated ground receptacles where the equipment calls for them, rack distribution and clean separation from general building power. Where a UPS is involved we wire the tie in and the maintenance bypass so the unit can be serviced without dropping the load. Covered by our new circuit and equipment installation.
Three Phase Panels and Service Upgrades
Most commercial space here runs 208Y/120 three phase, with some older buildings on 480 through step down transformers. We handle panels, feeders, distribution, motor and HVAC circuits, and service increases when a tenant’s equipment load exceeds what the building was designed around.
Standby Generator Installation
Whole home and light commercial standby units with an automatic transfer switch, sized from a real load calculation rather than a guess. Interest in backup power here climbed sharply after the storm damage Upper Dublin saw a few years ago, and it has not dropped since. Details on standby generator and transfer switch installation.
Service Mast and Storm Damage Repair
When a limb takes down the mast, weatherhead or service entrance cable, that is the property owner’s equipment, not the utility’s, and power will not come back until an electrician restores it. We handle the repair, coordinate the utility reconnect and pull the permit. These calls get priority.
Rewiring Stone and Older Homes
Solid masonry exterior walls have no cavity to fish, so the route runs through interior partitions, closet backs, floor bays and the attic, with surface raceway only where nothing else will work. We map it before quoting, because there is no honest way to price this from the curb.
Electrical Panel Upgrades
Moving a 60 or 100 amp residential service up to 200 amps, including the load calculation, meter socket, service entrance cable, new load center and the PECO coordination. Same standards as our residential electrical work across the region.
Repairs and Troubleshooting
Dead outlets, half-working circuits, GFCI devices tripping without cause, breakers that will not reset, equipment that misbehaves for no obvious reason. We trace with meters and thermal imaging rather than guesswork. Most single-fault fault tracing and electrical repair finishes in one visit.
Lighting Installation and Retrofits
Troffer and high bay LED retrofits with occupancy sensors in commercial space, recessed cans and fixture work in homes, plus exterior, parking area and exit and emergency lighting. See our lighting installation and retrofits.
EV Charging and Emergency Service
Level 2 chargers at home, and multi port commercial charging where the site and service support it. For power loss, a burning smell, water in a panel or storm damage, call 267-312-8232 for emergency electrical response. We also run structured and low voltage wiring alongside build outs.
What Working With TotalPower Actually Looks Like
Nothing starts until you have a flat price in writing. We diagnose first, quote second, and work third. No hourly meter running while somebody figures out where the fault is, and no revised number appearing after the ceiling tiles are out.
Commercial work happens when your business is not happening. Evenings, weekends, whatever your lease and your building management allow. In an occupied suite we plan the outage window before we plan anything else, because a circuit that takes four hours is a different job at nine in the morning than at nine at night.
Load calculations come before recommendations, in both markets. A recommendation without a calculation behind it is just a guess with a price attached, and it usually guesses upward. Sometimes the answer really is a service upgrade. Often it is a subpanel, a dedicated circuit or a load management device for a fraction of the cost.
Permits go through Upper Dublin Township, which runs its own code enforcement. We file, schedule the inspection and hand you the closeout paperwork, whether it is a residential panel swap or a commercial fit out.
Everything gets documented. Photographs of terminations, panel interiors, finished installs, and a panel schedule that actually matches the circuits. That matters to facilities managers, to insurers and to whoever owns the building next. Look through a record of finished work before you decide to call.
Same day slots stay open on weekdays. A business with no power and a house with no power both move to the front of the queue, and if the schedule is genuinely full we tell you rather than leaving you waiting.
From First Call to Final Sign Off
-
Tell us the address and the problem
For commercial, include the building, the suite and whether the space is occupied. For residential, the panel size and the age of the house if you know them. A lot of jobs get scoped on the phone before anyone gets dispatched.
-
Site visit, testing and load calculation
We test circuits, open panels, check grounding and bonding, and calculate rather than estimate for anything that adds load. You get a written flat price covering labor, materials, permit and inspection.
-
Permit filed, window agreed
Applications go to Upper Dublin Township and the inspection gets booked. For occupied commercial space we lock the after hours window here, so nobody finds out on the day that their floor is losing power.
-
The work, and the labeling
Drop cloths down, terminations torqued to spec, circuits labeled properly, work area cleared each day. Residential jobs get essential circuits back before we leave each evening. Commercial jobs get handed back ready for business hours.
-
Inspection, walkthrough, records
The inspector signs off, we walk you through what changed, and you keep the permit records, panel schedules and photographs. Then you call us directly if anything acts up.
What Electrical Work Costs in Fort Washington, PA
Price comes down to what the load calculation shows, how far and how difficult the runs are, whether the service or meter has to change, and whether the utility needs to disconnect. After hours commercial work carries a different rate than daytime residential, and that is priced into the quote rather than added afterward.
The ranges below reflect recent work in Fort Washington and the surrounding Upper Dublin area. Commercial fit outs and server room projects are quoted per scope after a walkthrough, because equipment lists and building conditions vary too much for a useful range.
| Job | Typical range | What moves the price |
|---|---|---|
| Service call and diagnosis | $175 to $375 | Circuits involved, access, time of day |
| Outlet, switch or fixture replacement | $150 to $450 | Box condition, ceiling height, fixture weight |
| Dedicated circuit added | $450 to $1,200 | Run length, wall construction, panel capacity |
| Server or comms room circuit package | $1,500 to $6,000 | Circuit count, isolated grounds, UPS tie in |
| 100 to 200 amp residential panel upgrade | $1,900 to $4,800 | Meter location, mast condition, permit and inspection |
| Service mast and weatherhead repair | $900 to $3,500 | Damage extent, mast height, utility coordination |
| Whole home standby generator | $7,000 to $18,000+ | Unit size, gas line work, pad, permits and clearances |
| Rewiring a stone or solid masonry home | $15,000 to $38,000+ | Wall construction, route availability, patching scope |
| Commercial fit out or lighting retrofit | Quoted per scope | Square footage, fixture count, after hours access |
Estimates for planned projects are free, commercial and residential alike. Diagnostic calls carry a service fee quoted before dispatch, credited toward the repair if you proceed the same day. Compare our panel and service capacity upgrades if you are weighing a targeted fix against added headroom.
Fort Washington and the Upper Dublin Service Area
We cover Fort Washington and the wider 19034 area, including the office park along Pennsylvania Avenue, Virginia Drive, Commerce Drive and Camp Hill Road, the residential streets off Bethlehem Pike and Susquehanna Road, and the older properties toward Militia Hill and Skippack Pike. All of it sits in Upper Dublin Township, which handles its own permits and inspections.
Nearby we take calls in Ambler, Dresher, Maple Glen, Oreland, Flourtown, Spring House, Blue Bell, Horsham, Plymouth Meeting and Conshohocken, plus the rest of Montgomery County. Philadelphia is where the company started, so we still run daily in Chestnut Hill, Mount Airy, Germantown, Roxborough, Center City, Northwest and Northeast Philadelphia, West Philadelphia and South Philly.
Beyond that we handle residential and commercial work across Bucks County, Delaware County and Chester County. If you are not sure whether your building falls inside our range, call and ask. Thirty seconds settles it.
Questions We Get From Fort Washington Customers
How much does an electrician cost in Fort Washington, PA?
Most service calls run $175 to $375 for diagnosis and a small repair. Residential panel upgrades usually land between $1,900 and $4,800, and a server room circuit package between $1,500 and $6,000. Commercial fit outs are quoted per scope after a walkthrough. Estimates for planned projects are free.
Do I need a permit for electrical work in Upper Dublin Township?
Yes, for most work beyond a simple fixture swap. Panel upgrades, service changes, new circuits, generators, rewiring and commercial fit outs all require a permit and inspection under the Pennsylvania Uniform Construction Code. Upper Dublin runs its own code enforcement. We file the application and hand you the closeout records.
What electrical does a server room need?
Dedicated circuits sized to the equipment load and separated from general building power, correct grounding, adequate cooling capacity on its own circuits, and surge protection upstream. Isolated ground receptacles are specified for some equipment. Sharing a rack with office receptacles causes voltage sag and unexplained reboots.
What is a UPS maintenance bypass and do I need one?
A bypass switch lets an uninterruptible power supply be serviced or replaced while the connected equipment keeps running on utility power. Without one, maintaining the UPS means taking the load down. If your equipment cannot tolerate a planned outage, the bypass is worth wiring in at installation.
Can you work in our office after hours?
Yes, and for occupied suites we usually recommend it. We schedule evenings and weekends around your operating hours, coordinate with property management on building access and after hours HVAC, and agree the outage window before the job is booked rather than on the day.
Who is responsible for a damaged electrical service mast?
The property owner, in most cases. The utility owns the line up to its connection point, but the mast, weatherhead, meter socket and service entrance cable belong to the building. A licensed electrician has to repair them and the utility will not reconnect until that work is done and inspected.
What size generator do I need for my house?
It depends what you want running during an outage. Essentials such as heat, refrigeration, a well pump and a few circuits usually need 11 to 14 kilowatts. Running a whole Fort Washington home including central air typically needs 20 to 26 kilowatts. We size it from an actual load calculation, not a rule of thumb.
How long does a standby generator take to install?
Most residential installations take two to three days on site once the unit and the gas work are lined up, plus permit and inspection time. Site prep, the pad, the gas line and the transfer switch make up most of it. Lead times on the equipment itself often exceed the install.
How do you rewire a stone house?
Not through the exterior walls. Solid masonry has no cavity, so we run through interior partitions, closet backs, floor bays, the attic and the basement, and use surface raceway only where nothing else works without real damage. Every one of these houses gets mapped before it gets quoted.
Can you do same day electrical repairs in Fort Washington?
Yes. We hold open slots each weekday for same day calls across Fort Washington, Ambler, Dresher and Maple Glen, and we run emergency service for power loss, burning smells, sparking outlets and storm damaged service equipment. Call 267-312-8232 early in the day for the best chance.
Is TotalPower Electrical licensed and insured?
Yes. TotalPower Electrical Services LLC carries HIC License PA197924 and liability insurance, and our technicians hold OSHA 30 certification. We register with the township whenever a permit requires it, and we can send our certificate of insurance to your property manager or building owner before we mobilize.
How often do emergency exit lights need to be tested?
Under NFPA 101, a functional test of at least 30 seconds every month and a full duration test of 90 minutes annually, with records kept. Most tenants find this out at a fire inspection rather than before one. We test, log the results and repair or replace failed units.
Is a whole house surge protector worth it?
Usually yes where there is equipment worth protecting. A panel mounted device clamps surges before they reach HVAC control boards, appliance electronics and network gear, which a power strip cannot do for anything hardwired. Installation takes about an hour and runs roughly $400 to $800.
Can I do my own electrical work in Pennsylvania?
Homeowners can legally do limited work on a property they own and occupy, but permits and inspections still apply. Anything touching the panel, service entrance or new circuits carries real shock and fire risk and frequently fails inspection when done without training. Commercial tenants cannot self perform this work.
How do I book an electrician with TotalPower?
Call or text 267-312-8232, email Totalpowerpa@gmail.com, or use the form on our contact page. Give us the address, what needs doing, and whether it is a home, an office suite or a whole building. We confirm an arrival window, give you a flat price, and start once you approve it.
Talk to a Licensed Electrician in Fort Washington Today
A suite that has to be live before Monday, a generator you have been meaning to price since the last outage, or a stone house with wiring older than the driveway. TotalPower Electrical Services looks at it properly and gives you a flat price before anything gets opened. Fifteen years, HIC License PA197924, OSHA 30 certified crews, and a phone that gets answered!
Call 267-312-8232, email Totalpowerpa@gmail.com, or send us the building details. You can also pull up our Google Maps listing.