Feasterville, PA Electrician for Panel Upgrades, Repairs and Rewiring
Panel upgrades, aluminum wiring repair, lighting, generators, pool and hot tub circuits and emergency service across Feasterville, Lower Southampton Township and lower Bucks County, with a flat price you approve before we start.
- ●HIC License PA197924
- ●15+ Years Experience
- ●OSHA 30 Certified Technicians
- ●Fully Insured
- ●Same Day Service Available
- ●Upfront Flat Pricing
TotalPower Electrical Services is a licensed electrical contractor serving Feasterville, PA and Lower Southampton Township with panel upgrades, aluminum wiring repair, rewiring, lighting, generators, repairs and emergency service. The company holds HIC License PA197924, employs OSHA 30 certified technicians, has 15 plus years of experience, and quotes flat pricing before work begins.
Feasterville filled in through the 1950s, 1960s and 1970s, and the housing reflects it. Ranchers and splits on generous lots off Bustleton Pike, most of them originally wired at 100 amps for a much smaller electrical life than the one they carry now. The late 1960s and early 1970s builds are where aluminum branch wiring turns up, and we find it here often enough that we check for it on any house of that vintage before quoting anything.
Our crews run daily in the city as licensed electricians in Philadelphia, which is a short run down Bustleton Avenue from most of the township. Every circuit gets tested. Every permit gets filed with Lower Southampton. You see the price in writing before anything gets opened up.
What Electrical Service Work Covers and the Signs of Bad Wiring in a House
Electrical service work runs from the utility connection at your meter to the last device on the last circuit. That covers the service entrance, meter socket, main panel and breakers, the grounding and bonding system, every branch circuit, and all the outlets, switches and fixtures they feed. A licensed electrician finds the actual fault instead of replacing parts and hoping, which is the difference between a repair that lasts and one you pay for twice.
A homeowner off Buck Road had us out because a dining room switch felt warm to the touch. Behind it we found aluminum conductors landed on a standard brass screw, discoloured and pitted where the two metals had been reacting for decades. Four more devices on that circuit looked the same. One warm switch was the symptom. The circuit was the actual job.
Call an electrician if you notice any of the following:
- Aluminum branch wiring, common in homes built here between roughly 1965 and 1975
- A 100 amp service running central air, a finished basement and a pool pump
- A Federal Pacific Stab-Lok or Zinsco panel, both known for breakers that fail to trip
- Breakers that trip under normal load, or a panel with no spare slots
- Lights that dim when the AC compressor, dryer or well pump starts
- Outlets or switch plates that feel warm, or show scorch marks
- A burning plastic smell with no obvious source
- Pool or outdoor equipment with no GFCI protection or proper bonding
- Two prong ungrounded outlets, or extension cords used as permanent wiring
- Buzzing from a switch, a receptacle or the panel itself
Our Electrical Services in Feasterville, PA
One crew, one point of contact, and nothing handed off to a subcontractor you never met.
Electrical Panel Upgrades and Service Changes
Moving a 100 amp service up to 200 amps is the job we run most often in Lower Southampton. We handle the load calculation, meter socket, service entrance cable, new load center and the PECO coordination. Same standards as our home electrical services across the region.
Aluminum Wiring Repair
The accepted fixes are pigtailing every device with approved connectors, or replacing the affected circuits with copper. Both are permitted and inspected work. We survey every device on the circuit first, because treating four outlets and leaving eight alone solves nothing. See our circuit and rewiring work.
Federal Pacific and Zinsco Panel Replacement
Both brands have a documented history of breakers that fail to trip under fault conditions, and replacement breakers do not solve it. The remedy is a full panel replacement. We test before recommending it, because nobody should replace a panel on a hunch.
Electrical Repairs and Troubleshooting
Dead outlets, half-working circuits, GFCI devices tripping without cause, breakers that will not reset. We trace faults with meters and thermal imaging rather than guesswork. Most single-fault electrical diagnostics and repairs finish in one visit.
Lighting Installation and Upgrades
Recessed LED cans, under cabinet runs, exterior floods, landscape lighting, dimmer conversions and fixture swaps. Ranchers and splits here often have shallow ceiling cavities, so we check clearance before anyone orders housings. See our lighting and fixture upgrades.
Generator Installation and Hookups
Whole home standby units with an automatic transfer switch, or a portable generator inlet with a code compliant interlock kit. Storms take out power across lower Bucks regularly, and homes on well and septic lose water along with the lights. Details on standby and portable generator hookups.
EV Charger Installation
Level 2 chargers on a dedicated 40 to 60 amp circuit, hardwired or on a NEMA 14-50 receptacle. We run a load calculation first. A 100 amp service in a 1960s rancher will not carry a 48 amp charger without an upgrade or a load management device.
Pool, Hot Tub and Outdoor Wiring
Pools need equipotential bonding, GFCI protection and a correctly sized pump circuit, and that is where most DIY pool wiring fails inspection. Hot tubs need a disconnect within sight of the unit. We also run underground feeds to sheds and detached garages in conduit rated for burial.
Basement and Addition Wiring
Finished basements need adequate circuits, AFCI protection and proper egress lighting, and an older panel rarely has room left for them. We also handle smart home and automation wiring while the walls are still open.
Emergency and Commercial Electrical Work
Power loss, a burning smell, water in a panel or storm damage to the service mast gets an emergency electrical callout on 267-312-8232. We also serve the retail and service businesses along Bustleton Pike and Street Road through our commercial electrical contractors.
Why Feasterville and Lower Southampton Property Owners Choose TotalPower
You get a flat price before the work starts. We diagnose, we quote, you approve. No clock running while somebody hunts for the fault, and no surprise change orders once the walls are open.
Aluminum wiring gets assessed honestly. Some contractors quote a full rewire on sight because it is the bigger ticket, and others ignore it entirely. Neither serves you. We survey the circuits, tell you whether approved connectors will do the job or whether replacement is genuinely warranted, and price both.
Permits are our job. Feasterville sits in Lower Southampton Township, which handles its own applications and inspections. Knowing the right office before filing keeps a panel job on schedule rather than losing a week to a bounced application.
Every technician on the truck holds OSHA 30 certification. On service changes, pool circuits and commercial work, the difference between a safe outcome and a bad one comes down to procedure rather than speed.
Documentation comes standard. We photograph terminations, panel interiors and finished installs, which matters when an insurer or a buyer’s inspector asks for proof. Browse recent finished projects before deciding whether to call.
Same day slots stay open on weekdays for repair calls. If the schedule is genuinely full, we say so rather than leaving you waiting on a truck that is not coming.
Our Process, From First Call to Final Inspection
-
Call or message with the details
Give us the address, the symptom, and your panel brand and size if you can read them off the door label. We ask questions on the phone because half the time we can tell you whether this is a $200 visit or a $4,500 project before dispatching anyone.
-
On site diagnosis and written quote
We test the circuits, open the panel, check grounding and bonding, and pull a few devices when aluminum is suspected. You get a written flat price. Nothing gets touched until you say go.
-
Permit and scheduling
Panel upgrades, service changes, aluminum remediation, new circuits, pool and hot tub circuits and rewiring get filed with Lower Southampton Township and scheduled with the inspector. Repairs that need no permit usually get handled the same visit.
-
The work, done to code
Drop cloths down, circuits labeled, terminations torqued to spec. On multi-day jobs we keep the house livable and restore essential circuits before we leave each evening.
-
Inspection, walkthrough and paperwork
The inspector signs off, we walk you through what changed, and you keep the permit records and photos for your insurer or a future buyer. Then you call us directly if anything acts up later.
How Much Does an Electrician Cost in Feasterville, PA
Four things move the price: the size of the service, the condition and type of existing wiring, how hard the runs are to reach, and whether PECO has to disconnect and reconnect. Aluminum remediation is priced by device count, not square footage, which is why the survey comes before the quote.
The ranges below reflect recent work in Feasterville and the surrounding lower Bucks townships. Your written quote might land outside them, and we will explain exactly why if it does. We do not quote low to get in the door and revise upward later.
| Job | Typical range | What moves the price |
|---|---|---|
| Service call and diagnosis | $150 to $350 | Number of circuits involved, access, time of day |
| Outlet, switch or fixture replacement | $150 to $400 | Box condition, whether a ground and neutral are present |
| Dedicated circuit added | $400 to $1,000 | Distance from panel, wall finish, spare panel space |
| Aluminum wiring pigtail remediation | $1,500 to $5,000 | Number of devices, access, whether boxes need replacing |
| 100 to 200 amp panel upgrade | $1,800 to $4,500 | Meter location, mast condition, permit and inspection |
| Federal Pacific or Zinsco panel replacement | $2,000 to $4,500 | Whether the service size changes at the same time |
| Pool wiring, bonding and pump circuit | $800 to $2,200 | Distance to panel, trenching, equipment list |
| Hot tub circuit and disconnect | $800 to $2,000 | Distance to panel, trenching, service capacity |
| Level 2 EV charger install | $800 to $2,500 | Run length, garage location, whether the service supports it |
| Standby generator with transfer switch | $6,000 to $16,000+ | Unit size, gas line work, pad and clearances |
Estimates for planned projects are free. Diagnostic calls carry a service fee that we tell you before dispatch, and it gets credited toward the repair if you move forward the same day. Compare our service and panel upgrades if you are weighing a targeted repair against added capacity.
Areas We Serve Around Feasterville and Lower Bucks County
We cover Feasterville and the rest of Lower Southampton Township, including the neighborhoods off Bustleton Pike, Street Road, Buck Road and Brownsville Road, across zip code 19053. Southampton and Trevose addresses nearby fall into different municipalities, and we confirm which office permits your job before filing anything.
Nearby we take calls in Southampton, Churchville, Richboro, Holland, Langhorne, Warminster, Bensalem, Huntingdon Valley and the rest of Bucks County. Philadelphia is where the company started, so we still run daily in Northeast Philadelphia, including Somerton and Bustleton, along with Center City, Northwest Philadelphia, West Philadelphia and South Philly, plus Roxborough, Germantown, Kensington and Fishtown.
Farther out we handle residential and commercial work in Montgomery County, Delaware County and Chester County. Not sure whether your address falls inside our range? Call and ask. It takes about thirty seconds.
Electrician Feasterville PA Frequently Asked Questions
How much does an electrician cost in Feasterville, PA?
Most Feasterville service calls run between $150 and $350 for diagnosis and a small repair. Panel upgrades usually land between $1,800 and $4,500 depending on amperage and meter location, and aluminum wiring remediation typically runs $1,500 to $5,000 by device count. We quote a flat price before any work starts.
Do I need a permit for electrical work in Lower Southampton Township?
Yes, for most work beyond a simple fixture swap. Panel upgrades, service changes, new circuits, pool and hot tub circuits, aluminum remediation and rewiring all require a permit and inspection under the Pennsylvania Uniform Construction Code. We file with the township and hand you the closeout paperwork.
Is aluminum wiring dangerous in a house?
It can be. Aluminum branch wiring expands and contracts more than copper as it heats, which loosens terminations over decades and creates hot connections behind the wall. It also corrodes where it meets standard brass or steel terminals. Feasterville homes built between roughly 1965 and 1975 commonly have it.
How do you fix aluminum wiring without rewiring?
By pigtailing. We connect a short copper lead to the aluminum conductor at every device using connectors approved for that purpose, then land the copper on the outlet or switch. It is permitted, inspected work and costs far less than replacing circuits. We survey every device before quoting.
Is a Federal Pacific panel dangerous?
It can be. Federal Pacific Stab-Lok breakers have a documented history of failing to trip under fault conditions, which means an overloaded circuit can keep heating instead of shutting off. Replacement breakers do not fix it. The accepted remedy is replacing the panel, and we test before recommending that.
Can you do same day electrical repairs in Feasterville?
Yes. We hold open slots each weekday for same day calls across Feasterville, Southampton, Churchville and Holland, and we run emergency service for power loss, burning smells and sparking outlets. Call 267-312-8232 early in the day for the best chance at a same day arrival.
Is TotalPower Electrical licensed and insured?
Yes. TotalPower Electrical Services LLC carries HIC License PA197924 and liability insurance, and our technicians hold OSHA 30 certification. We register with the township whenever a permit requires it, and we can send our insurance certificate to your property manager or HOA before we start.
What are the signs I need an electrical panel upgrade?
A 100 amp service in a house with central air, a pool and modern appliances, a panel with no spare slots, breakers tripping under normal load, or lights dimming when the dryer or AC starts. Rust or scorch marks inside the enclosure mean you should call right away.
How long does an electrical panel upgrade take?
Most 200 amp panel upgrades take one full day, roughly six to nine hours on site. Add time if PECO has to disconnect and reconnect the service drop, or if the meter socket and mast need replacing. Township inspection usually follows within a few business days, and power is back the same day.
Does an above ground pool need a bonded electrical connection?
Yes. The National Electrical Code requires equipotential bonding for pool structures, pumps and metal parts within reach of the water, plus GFCI protection on the circuits serving them. Most DIY pool wiring fails inspection on bonding. We size the pump circuit, bond the equipment and pull the permit.
Does a finished basement need AFCI protection?
Yes, in most cases. Current code requires arc fault protection on branch circuits serving finished living spaces, and a finished basement counts. Basements also require GFCI protection on receptacles. Both get inspected, so basement work done without a permit usually has to be corrected before a sale.
Can I do my own electrical work in Pennsylvania?
Homeowners can legally do limited work on a property they own and occupy, but permits and inspections still apply. Anything touching the panel, service entrance or new circuits carries real shock and fire risk and often fails inspection when done without training. Insurance claims also get denied for unpermitted DIY wiring.
Is electrical work covered by homeowners insurance?
Sometimes. Most policies cover damage from a sudden electrical failure, such as a fire or a surge that destroys appliances, but they do not pay to upgrade old or worn wiring. Carriers in Bucks County also ask about aluminum wiring, fuse panels and Federal Pacific equipment before quoting.
Do you install hot tub and outdoor circuits?
Yes. A hot tub needs a dedicated GFCI protected circuit sized to the unit and a disconnect within sight of it, and the run usually requires trenching in conduit rated for direct burial. All of it is permitted and inspected work. We size the circuit from the manufacturer’s specification.
How do I book an electrician with TotalPower?
Call or text 267-312-8232, email Totalpowerpa@gmail.com, or send the form on our contact page. Tell us your address, the problem, and your panel brand and size if you know them. We confirm an arrival window, give you a flat price on site, and begin once you approve it.
Talk to a Licensed Electrician in Feasterville Today
One warm switch plate or fifty year old aluminum behind every device, the answer starts the same way. TotalPower Electrical Services gives you a straight diagnosis and a flat price before anything gets opened up. Fifteen years, HIC License PA197924, OSHA 30 certified crews, and a phone that gets answered!
Call 267-312-8232, email Totalpowerpa@gmail.com, or tell us about the work. You can also open us on Google Maps.