Horsham, PA Electrician for Homes, Offices and Commercial Buildings
Panel upgrades, repairs, EV chargers and generators for homes, plus three phase work, tenant fit outs and lighting retrofits for the Horsham office and flex corridor. Flat pricing you approve before we start.
- ●HIC License PA197924
- ●15+ Years Experience
- ●OSHA 30 Certified Technicians
- ●Fully Insured
- ●Same Day Service Available
- ●Upfront Flat Pricing
TotalPower Electrical Services is a licensed electrical contractor serving Horsham, PA and Montgomery County with residential panel upgrades, repairs, EV chargers and generators, plus commercial three phase work, tenant fit outs and lighting retrofits. The company holds HIC License PA197924, employs OSHA 30 certified technicians, has 15 plus years of experience, and quotes flat pricing before work begins.
Horsham runs two ways at once, and our schedule reflects that. Residential neighborhoods of 1970s and 1980s colonials and splits, most of them wired at 100 or 150 amps and now carrying central air, a finished basement and sometimes a car. Then the office parks, flex buildings and light industrial space along Welsh Road, Blair Mill Road and Horsham Road, where the work is three phase panels, suite fit outs and lighting nobody has touched since the fixtures were fluorescent.
Our crews run daily in the city as licensed electricians in Philadelphia, so commercial and residential are both routine rather than one being a sideline. Every load gets calculated. Every permit gets filed with Horsham Township. You see the price in writing before anything gets opened up.
What Electrical Service Work Covers and the Signs of Bad Wiring in a House
Electrical service work runs from the utility connection at your meter to the last device on the last circuit. That covers the service entrance, meter socket, main panel and breakers, subpanels and feeders, the grounding and bonding system, every branch circuit, and all the devices they feed. A licensed electrician runs the numbers before adding load rather than guessing, which is the difference between a job that passes inspection and one that gets torn back out.
A homeowner near Babylon Road called us about breakers tripping whenever the dryer and the basement circuit ran together. The panel was a 150 amp box, which sounds like plenty until you count what had been added since 1979. Central air, a heat pump water heater, a finished basement and a workshop subpanel that a previous owner had fed off a 30 amp breaker. The calculation had been over for years. Nobody had ever checked.
Call an electrician if you notice any of the following:
- A 100 or 150 amp service in a house with central air and a finished basement
- A panel with no open slots, or tandem breakers doubled into most positions
- Breakers that trip when two large appliances run at once
- Lights that dim when the AC compressor, dryer or dishwasher starts
- Plans to add an EV charger, hot tub, pool heater or basement build out
- Outlets or switch plates that feel warm, or show scorch marks
- A burning plastic smell with no obvious source
- Subpanels or added circuits from a previous owner with no permit record
- Two prong ungrounded outlets, or extension cords used as permanent wiring
- Buzzing from a switch, a receptacle or the panel itself
Our Electrical Services in Horsham, PA
One crew, one point of contact, and nothing handed off to a subcontractor you never met.
Electrical Panel Upgrades and Service Changes
Moving a 100 or 150 amp service up to 200 amps is the job we run most often in Horsham Township. We handle the load calculation, meter socket, service entrance cable, new load center and the PECO coordination, the same way our residential electrical work runs region wide.
Subpanel Installation
When the main panel has no slots left but the service itself is adequate, a subpanel is usually the cheaper answer. It gives a finished basement, garage or workshop its own circuits without touching the meter. Covered under our new circuit and subpanel installation.
EV Charger Installation
Level 2 chargers on a dedicated 40 to 60 amp circuit, hardwired or on a NEMA 14-50 receptacle. We calculate first. A 150 amp service with a heat pump already on it may need a load management device instead of a full upgrade, and that saves you thousands.
Electrical Repairs and Troubleshooting
Dead outlets, half-working circuits, GFCI devices tripping without cause, breakers that will not reset. We trace faults with meters and thermal imaging rather than guesswork. Most single-fault troubleshooting and electrical repairs finish in one visit.
Lighting Installation and Upgrades
Recessed LED cans, under cabinet runs, exterior floods, landscape lighting, dimmer conversions and fixture swaps during a kitchen or bath renovation. Two story foyers need an access plan before anyone quotes a fixture change. See our lighting installation and fixture upgrades.
Generator Installation and Hookups
Whole home standby units with an automatic transfer switch, or a portable generator inlet with a code compliant interlock kit. We size from a real load calculation, because an undersized unit that trips out mid storm is worse than none. Details on standby generator and transfer switch work.
Basement, Hot Tub and Outdoor Wiring
Finished basements need adequate circuits, AFCI protection and proper egress lighting. Hot tubs need a dedicated GFCI circuit and a disconnect within sight. We also run smart home and structured wiring while the walls are still open.
Commercial Three Phase Work
Office parks and flex buildings here mostly run 208Y/120 three phase, and some of the older industrial space runs 480 with step down transformers. We handle panels, feeders, distribution, motor circuits and code correction across the Horsham commercial corridor.
Tenant Fit Outs and Lighting Retrofits
New suite layouts, demising walls, added circuits, data and power in open plan office, plus high bay and troffer LED retrofits with occupancy sensors. Our commercial electrical contracting works nights and weekends so tenants keep operating.
Emergency Electrical Service
Partial power loss, a burning smell, water in a panel, storm damage to the service mast, a business that cannot open. Call 267-312-8232 for after hours emergency electricians, and we will tell you what to shut off while we are on the way.
Why Horsham Township Homeowners and Businesses Choose TotalPower
You get a flat price before the work starts. We diagnose, we quote, you approve. No clock running while somebody works out what is needed, and no change orders surfacing after the ceiling is open.
Commercial work gets scheduled around your operation, not ours. Suite fit outs, panel work and lighting retrofits run nights and weekends in occupied buildings, and we coordinate with property managers on access, freight elevators and after hours HVAC rather than leaving you to sort it out.
Load calculations come before recommendations. Plenty of contractors quote a service upgrade for every EV charger because it is the bigger ticket. Sometimes that is correct. Often a subpanel or a load management device does the job for far less, and you deserve to know which situation you are actually in.
Permits are our job. Horsham Township has its own code enforcement office, which keeps filing and inspection straightforward, and we handle it from application through final sign off. Unpermitted work from a previous owner surfaces during a sale, not before it, and correcting it then costs more.
Every technician on the truck holds OSHA 30 certification, and work gets documented with photographs of terminations, panel interiors and finished installs. Browse photos of work we have finished before deciding whether to call.
Same day slots stay open on weekdays for repair calls. If the schedule is genuinely full, we say so rather than leaving you waiting on a truck that is not coming.
Our Process, From First Call to Final Inspection
-
Call or message with the details
Give us the address, what needs doing, and your panel size if you know it. For commercial work, tell us the building, the suite and whether the space is occupied. We can often scope the job on the phone before dispatching anyone.
-
On site assessment and written quote
We test circuits, open the panel, check grounding and bonding, and run a load calculation for anything that adds demand. You get a written flat price covering materials, labor, permit and inspection. Nothing gets touched until you approve it.
-
Permit and scheduling
Panel upgrades, subpanels, new circuits, EV chargers, hot tub circuits, generators and commercial fit outs get filed with Horsham Township and scheduled with the inspector. Occupied commercial work gets slotted for nights or weekends at this stage.
-
The work, done to code
Drop cloths down, circuits labeled, terminations torqued to spec, work areas cleaned each day. On multi-day residential jobs we restore essential circuits before leaving. On commercial jobs we leave the space usable for business hours.
-
Inspection, walkthrough and paperwork
The inspector signs off, we walk you through what changed, and you keep the permit records and photos for your files, your insurer or your landlord. Then you call us directly if anything acts up later.
How Much Does an Electrician Cost in Horsham, PA
Four things move the price: what the load calculation shows, the distance and difficulty of the runs, whether the meter or service has to change, and whether the utility needs to disconnect. Commercial work carries a different rate structure than residential, mainly because of after hours scheduling and three phase equipment.
The ranges below reflect recent work in Horsham and the surrounding Montgomery County townships. Your written quote might land outside them, and we will explain exactly why if it does. Commercial projects are quoted per scope after a walkthrough, since no two suites are alike.
| Job | Typical range | What moves the price |
|---|---|---|
| Service call and diagnosis | $150 to $350 | Number of circuits involved, access, time of day |
| Outlet, switch or fixture replacement | $150 to $400 | Box condition, ceiling height, fixture weight |
| Dedicated circuit added | $400 to $1,000 | Distance from panel, finished walls, spare panel space |
| Subpanel installation | $1,200 to $2,800 | Feeder length, panel size, conduit vs cable run |
| 100 or 150 to 200 amp panel upgrade | $1,900 to $4,500 | Meter location, mast condition, permit and inspection |
| Level 2 EV charger install | $800 to $2,400 | Run length, garage location, load management if needed |
| Hot tub circuit and disconnect | $800 to $2,000 | Distance to panel, trenching, service capacity |
| Standby generator with transfer switch | $6,500 to $17,000+ | Unit size, gas line work, pad and clearances |
| Commercial fit out or lighting retrofit | Quoted per scope | Square footage, fixture count, after hours access |
Estimates for planned projects are free, residential and commercial both. Diagnostic calls carry a service fee that we tell you before dispatch, and it gets credited toward the repair if you move forward the same day. Compare our panel and service capacity upgrades if you are weighing a subpanel against a full service change.
Areas We Serve Around Horsham and Montgomery County
We cover all of Horsham Township, including Prospectville, the neighborhoods off Horsham Road, Babylon Road, County Line Road and Norristown Road, and the office and flex corridor along Welsh Road, Blair Mill Road and Easton Road. That spans zip code 19044, and parts of the township carry Ambler and Hatboro addresses.
Nearby we take calls in Hatboro, Ambler, Dresher, Maple Glen, Willow Grove, Montgomeryville, Lansdale, Blue Bell and across the county line into Warminster and Warrington in Bucks County. Philadelphia is where the company started, so we still run daily in Northeast Philadelphia, Northwest Philadelphia, Center City, West Philadelphia and South Philly, plus Roxborough, Germantown, Kensington and Fishtown.
Farther out we handle residential and commercial work in Delaware County and Chester County. Not sure whether your address or building falls inside our range? Call and ask. It takes about thirty seconds.
Electrician Horsham PA Frequently Asked Questions
How much does an electrician cost in Horsham, PA?
Most Horsham service calls run between $150 and $350 for diagnosis and a small repair. Panel upgrades usually land between $1,900 and $4,500, and a subpanel typically runs $1,200 to $2,800. Commercial fit outs and lighting retrofits are quoted per scope after a walkthrough. Estimates for planned projects are free.
Do I need a permit for electrical work in Horsham Township?
Yes, for most work beyond a simple fixture swap. Panel upgrades, subpanels, new circuits, EV chargers, hot tub circuits, generators and commercial fit outs all require a permit and inspection under the Pennsylvania Uniform Construction Code, filed through Horsham Township code enforcement. We handle the filing and closeout.
Do you work on commercial properties in Horsham?
Yes, and it is a large part of what we do here. We handle three phase panels and feeders, tenant fit outs, added circuits, high bay and troffer LED retrofits, exit and emergency lighting and code correction across the Welsh Road, Blair Mill Road and Horsham Road corridor. We schedule nights and weekends in occupied buildings.
What is three phase power and does my business need it?
Three phase delivers power on three alternating conductors instead of one, which runs motors and heavy equipment more efficiently and evenly. Most Horsham office and flex buildings already have 208Y/120 three phase service. You need it for larger HVAC, elevators, commercial kitchen equipment and most machinery.
How often do emergency exit lights need to be tested?
Under NFPA 101, emergency and exit lighting requires a functional test of at least 30 seconds every month and a full duration test of 90 minutes once a year, with records kept. Many Horsham commercial tenants discover this at a fire inspection. We test, document and repair or replace failed units.
Can I add an EV charger to a 200 amp panel?
Usually yes, but not always. A 200 amp service already carrying a heat pump, electric water heater and finished basement can be near its calculated limit. We run a load calculation first. If it comes out tight, a load management device often costs far less than a service upgrade and works just as well.
Is a 150 amp service enough for a house?
It depends on the load, not the square footage. A 150 amp service handles a gas heated home with standard appliances comfortably. It gets tight once you add central air, an electric water heater, a finished basement and an EV charger. A load calculation gives you the real answer in about twenty minutes on site.
Can you do same day electrical repairs in Horsham?
Yes. We hold open slots each weekday for same day calls across Horsham, Hatboro, Ambler, Willow Grove and Warminster, and we run emergency service for power loss, burning smells and sparking outlets. Call 267-312-8232 early in the day for the best chance at a same day arrival.
Is TotalPower Electrical licensed and insured?
Yes. TotalPower Electrical Services LLC carries HIC License PA197924 and liability insurance, and our technicians hold OSHA 30 certification. We register with the township whenever a permit requires it, and we can send our insurance certificate to your property manager, landlord or HOA before we start.
What are the signs I need an electrical panel upgrade?
A 100 or 150 amp service in a house with central air and a finished basement, a panel with no open slots, breakers tripping when two appliances run together, or lights dimming when the compressor cycles. Warm panel covers or scorch marks mean you should call right away.
How long does an electrical panel upgrade take?
Most 200 amp panel upgrades take one full day, roughly six to nine hours on site. Add time if PECO has to disconnect and reconnect the service drop, or if the meter socket needs replacing. A subpanel installation is usually a half day. Inspection follows within a few business days.
Does a finished basement need AFCI protection?
Yes, in most cases. Current code requires arc fault protection on branch circuits serving finished living spaces, and a finished basement counts. Basements also require GFCI protection on receptacles. Both get inspected, so basement work done without a permit usually has to be corrected before a sale.
Can I do my own electrical work in Pennsylvania?
Homeowners can legally do limited work on a property they own and occupy, but permits and inspections still apply. Anything touching the panel, service entrance or new circuits carries real shock and fire risk and often fails inspection when done without training. Commercial property owners cannot self perform tenant work.
Is electrical work covered by homeowners insurance?
Sometimes. Most policies cover damage from a sudden electrical failure, such as a fire or a surge that destroys appliances, but they do not pay to upgrade old or worn wiring. Carriers in Montgomery County also ask about panel brand, service size and unpermitted work before quoting.
How do I book an electrician with TotalPower?
Call or text 267-312-8232, email Totalpowerpa@gmail.com, or send the form on our contact page. Tell us the address, what needs doing, and your panel size or building suite if you know it. We confirm an arrival window, give you a flat price, and begin once you approve it.
Talk to a Licensed Electrician in Horsham Today
A panel that ran out of room two renovations ago, or a suite that has to be ready before Monday. TotalPower Electrical Services gives you a straight assessment and a flat price before anything gets opened up. Fifteen years, HIC License PA197924, OSHA 30 certified crews, and a phone that gets answered!
Call 267-312-8232, email Totalpowerpa@gmail.com, or tell us about the job. You can also view our Google Maps listing.